Power & Communication Towers
Coating Solution Center

Surface treatment:Sand or grind to Sa2.5 / St3 grade, remove oil, rust, and dust, keep substrate dry; galvanized parts must be sanded to a rough surface.
Mixing:Before application, thoroughly mix the coating to ensure uniformity and avoid color variation and sedimentation.
Thinning:When viscosity is too high, add ≤5% clean water (by weight) for dilution. Stir well before use.
Construction:XGE-920 Primer (dry film 45-55μm) + XGE-921 Topcoat (dry film 40-50μm), can be applied by brush, roller, or air spray.
Drying:Dry on surface approximately 10-30 minutes (at 20°C), cure for 24 hours; Repaint interval ≥4 hours (at 20°C).
Construction conditions:Ambient temperature 5-35℃, relative humidity ≤80%, substrate temperature must be 3℃ above the dew point.
Notes:Construction prohibited in rainy, foggy, or dew-covered conditions; tools should be cleaned immediately with water; coatings should be stored sealed at 5-35°C in a cool, dry place, with a shelf life of 12 months.

Surface treatment:Sand or grind to Sa2.5 / St3 grade, remove oil, rust, and dust, keep substrate dry; galvanized parts must be sanded to a rough surface.
Mixing:Before application, thoroughly mix the coating to ensure uniformity and avoid color variation and sedimentation.
Thinning:When viscosity is too high, add ≤5% clean water (by weight) for dilution. Stir well before use.
Construction:XGE-920 Primer one coat (dry film 45-55μm) + XGE-603 Silver Topcoat one coat (dry film 40-50μm), can be applied by brush, roller, or air spray.
Drying:Dry on surface approximately 10-30 minutes (at 20°C), cure for 24 hours; Repaint interval ≥4 hours (at 20°C).
Construction conditions:Ambient temperature 5-35℃, relative humidity ≤80%, substrate temperature must be 3℃ above the dew point.
Notes:Construction prohibited in rainy, foggy, or dew-covered conditions; tools should be cleaned immediately with water; coatings should be stored sealed at 5-35°C in a cool, dry place, with a shelf life of 12 months.

Surface treatment:Sandblasting to Sa2.5 grade (recommended) or power tool cleaning St3 grade for thorough degreasing, rust removal, and dust removal.
Mixing:Before application, thoroughly mix the coating to ensure uniformity and avoid color variation and sedimentation.
Thinning:When viscosity is too high, add ≤5% clean water (by weight) for dilution. Stir well before use.
Construction:XGE-HY epoxy primer in one coat (dry film 50-60μm) + XGE-603 topcoat in one coat (dry film 40-50μm); airless spraying yields the best results.
Drying:Dry on surface approximately 10-30 minutes (at 20°C), cure for 24 hours; Repaint interval ≥4 hours (at 20°C).
Construction conditions:Ambient temperature 5-35℃, relative humidity ≤80%, substrate temperature must be 3℃ above the dew point.
Notes:Construction prohibited in rainy, foggy, or dew-covered conditions; tools should be cleaned immediately with water; coatings should be stored sealed at 5-35°C in a cool, dry place, with a shelf life of 12 months.

Surface treatment:Sandblasting to Sa2.5 grade for degreasing, rust removal, and dust removal; for high salt spray environments, it is recommended to add an epoxy zinc-rich primer.
Mixing:Before application, thoroughly mix the coating to ensure uniformity and avoid color variation and sedimentation.
Thinning:When viscosity is too high, add ≤5% clean water (by weight) for dilution. Stir well before use.
Construction:XGE-HY Primer (dry film 50-60μm) + XGE-930 Fluorocarbon Topcoat (dry film 40-50μm), air spray is the best method.
Drying:Dry on surface approximately 10-30 minutes (at 20°C), cure for 24 hours; Repaint interval ≥4 hours (at 20°C).
Construction conditions:Ambient temperature 5-35℃, relative humidity ≤80%, substrate temperature must be 3℃ above the dew point.
Notes:Construction prohibited in rainy, foggy, or dew-covered conditions; tools should be cleaned immediately with water; coatings should be stored sealed at 5-35°C in a cool, dry place, with a shelf life of 12 months.

Surface treatment:Sand or grind to Sa2.5 / St3 grade, remove oil, rust, and dust, keep substrate dry.
Mixing:Before application, thoroughly mix the coating to ensure uniformity and avoid color variation and sedimentation.
Thinning:When viscosity is too high, add ≤5% clean water (by weight) for dilution. Stir well before use.
Construction:XGE-621 Integrated Base Paint for direct application, one coat sufficient (dry film 50-65μm), no primer required, quick-drying, suitable for projects with tight schedules.
Drying:Dry on surface approximately 10-30 minutes (at 20°C), cure for 24 hours; Repaint interval ≥4 hours (at 20°C).
Construction conditions:Ambient temperature 5-35℃, relative humidity ≤80%, substrate temperature must be 3℃ above the dew point.
Notes:Construction prohibited in rainy, foggy, or dew-covered conditions; tools should be cleaned immediately with water; coatings should be stored sealed at 5-35°C in a cool, dry place, with a shelf life of 12 months.